♦The shell is made of high-quality flame-retardant and transparent materials, which is strong and wear-resistant, resistant to high temperatures and corrosion, and is dust-proof and safer.
♦Widen and thicken the overall silver alloy contacts, which can carry greater current, have stronger conductivity, sensitive response and long electrical life.
♦High-purity copper coil can withstand large voltages and has a long service life of more than 10 million times.
♦High-quality nickel-plated environmentally friendly screws, translucent and rust-free, with stronger electrical conductivity and tighter wiring with gaskets.
The cablelead-out part is set toincreexse lhe caale lock.The lead-out part of tne cable wllnot be Falure due to weer.
The contacts are plated wth 24K gold.Pass CE UL.C-ULLoad capacity10A 250VAC30DC
Tne surface of the shell is baked withplslic ireaiment, which is resistant toeruironmen, ahresin and sgng
Improwe the size of the bottom platesin.cture and increese the botimNon-slp nbber pad area, producedc.mng operston The prod.ct isnot eesy to slde, and is not eesyto tl on its side.
♦The reed switch is dedicated to signal control.
♦Watemproof micro switch-protection grade can reach lP67.
♦Multiple interface options: audio, serial port, USB, aviation plug, etc.
♦Built-in V15F-01C instantaneous micro switch, obtained UL, c-UL, VDE, CE certification, The contacts are plated with 24K gold with large load capacity and high contact reliability.
♦Standard configuration RVB 0.5mm2X2-core parallel parallel x 2m (light gray) cable.
♦Foot switch 6.3 audio plug, DB serial plug, USB plug can be customized if needed;
♦Waterproof foot switch can be customized;
♦The cable is not standard and must be purchased separately.
PV DC BR-30 Fuse Holder was designed and manufactured, complyings withthe standard LEC60947-3 The Rated Current up to 30A, rated voltage up to1000V DC.
It applied for PV DC combiner box, inverter etc, with the mainfunction ofover-current protection and effective disconnection
♦Light weight resin control box with protection grade of Ip65.
♦The opening type can be used to install ∅ 22 series control components.
♦No hole type can be installed in the internal terminal block, as a transfer control box.
♦In addition, it is equipped with a yellow appearance for emergency stop and a contact block protection type control box which can be installed in the panel's control component wiring part and has a protection grade of IP65.
♦The product adopts a cam structure inside, which is reliable and safe to use. The line on-off selection is flexible, and different on-off methods can be selected according to the customer's usage environment.
♦Complies with the general provisions for low-voltage switchgear and controlgear。
♦Normal conditions of use:The surrounding air temperature is between -25°C and +55°. The altitude of the installation site does not exceed 2000m. The operating temperature is less than or equal to 90%RH. The installation category is Category III. The minimum number of floors for power distribution and control level products is 1, and the maximum number of floors is 12.
♦With alloy contacts, electrical special silver long life and highreliability.
♦Small size,space-saving installation.
♦Construct a protective finger to make the operation safe.
♦With a varielyofinstallation,ease of application of variouspurpose(panel mount,rail mount, sealed switch box type).
♦lP66 degree of protection
♦Installation Options: Screw Installation, Rail Installation or Door Installation
♦Can padlock, more safely and reliable, diameter of lock is Ø4-Ø5mm
♦Standard: EN60947-3 and GB14048.3.
♦Degree of Protection: IP20 or IP67(with Plastic or Aluminium enclosures).
♦With buzzer protection level: IP65
♦Flashing frequency: 60-90 times/min
♦Turn light frequency: 60-90 times/min
♦LED modules can be freely combined, you can freely increase
or decrease
♦Lampshade: PC
♦Light body: ABS
♦Straight: AL